oreocomputers.blogg.se

Vortex viper red dot
Vortex viper red dot











vortex viper red dot vortex viper red dot

The adjustment gradations are a full MOA, which is an interesting choice that makes a lot of sense given the short ranges that this sight is intended for. Like all red dots, the design allows it to be virtually parallax-free (there is some parallax, but it is minimal), and it has a max windage and elevation adjustment of 120 MOA, which is quite a bit. The Vortex Viper is a small red dot sight with a 6 MOA center dot and nothing else on the reticle. 3 MOA dot for taking shots between 50 - 100 yards.Up to 30,000 hours of battery life up to 30,000 hours of battery life on a single CR2032.Let’s take a closer look at what separates these two and which would make you the best addition to your collection. There are also holographic sights, but we won’t really get into those. There is the tube style, which is more similar in appearance to a small scope, and then there’s the reflex style that both of these Vortex scopes are designed with.

vortex viper red dot

Red dot sights are optics that mount on a firearm and do not provide magnification but vastly improve the speed of target acquisition and accuracy over the iron sights that come stock with most guns. These two red dots have a lot of similarities, but also some key differences that could make the difference in which one you should buy. There are countless red dot options out there, but for this comparison, we want to stick with just the Viper vs Venom. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.Ĭlick here to see a video from Vortex on how to install our red dot base on a slide.Vortex is known for their quality optics across the spectrum of price points, and they have two flagship entries into the red dot space: the Viper and the Venom. This product should be installed and checked by a qualified gunsmith. Modification of your firearm may nullify the manufacturer's warranty. The screws that are included with this mount require a 5/64'' allen wrench for installation. Apply blue Loctite to the provided mounting screwsĢ Button Head Cap Screws - Provided for Vortex Viper and Venom SightsĢ Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Place the red dot sight on the EGW Sight Mount Install the EGW Sight Mount in the dovetail Red Dot Mounting Plate Installation Instructions You can take our mount off and replace your rear sight at any time. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. Glock 48 (Our mount is wider than the slide, but it will still work)ĭoes not fit ANY/ALL Glock slides that are already cut for optics.Glock 43x (Our mount is wider than the slide, but it will still work).

vortex viper red dot

  • Glock 43 (Our mount is wider than the slide, but it will still work).
  • Glock 42 (Our mount is wider than the slide, but it will still work).
  • Glock 36 (Our mount is wider than the slide, but it will still work).
  • This mount fits all generation Glocks with only rear sight dovetail cuts (including but not limited to): The dovetail has a progressive taper to allow for easier install. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.Īre you looking to replace your factory Glock rear sight with a red dot mounting plate? Our red dot adapter plates for Glocks easily let you mount your red dot to your gun with no modifications to the slide! Our Glock red dot sight mounts are meant to be installed from the left to the right. These dots may not fit properly on the posts on the plate. Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. *All ADE mounts require 6-32 x 3/8" screws. The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.













    Vortex viper red dot